Looking for:
Powerflex 525 manual download |
ALLEN-BRADLEY POWERFLEX USER MANUAL Pdf Download | ManualsLib
Hide thumbs Also See for PowerFlex : User manual pagesOriginal instructions manual 48 pagesApplication technique powerflex 525 manual download pages. Table Of Contents.
Quick Links. Table of Contents. Previous Page. Next Page. Trademarks not belonging to Rockwell Automation are property powerflex 525 manual download their respective companies. Page 5 EMC Instructions For information on See page Minimum Mounting Clearances Appendix B for mounting amnual. These devices must be disconnected if the drive is installed on an ungrounded or resistive grounded distribution system.
Listed in the Input Power Conditions table below are certain input power conditions powerflex 525 manual download may cause component damage or reduction in product life. Safety Ground - PE This is the safety ground for the drive that is required by code. One of these points must be connected to adjacent building downlooad girder, joista floor ground rod or bus bar.
This alesis nitro drum module manual should be installed with either input fuses or an input circuit breaker. Separating the Power and Control Module 1. Press and hold down the catch on both sides of the frame cover, then pull out and swing upwards to remove Frames B E only. Hold the sides and top of the Control Module firmly, then pull out to separate it from the Power Module.
Connecting citrix workspace app 19.12.7000 Power and Control Module 1. Push the top cover of the Control Module towards the Power Module to rownload it. Insert the catch at the top of the frame cover into the Power Module, manua swing the frame cover to snap the side catches onto powerflex 525 manual download Power Module Frames B To remove: 1. Press and hold down the arrow on the front of the cover. Slide the front cover down to remove from the Control Module. Re-attach the front cover when wiring is complete.
Press and hold down the locking tab on the terminal guard. Slide the terminal guard powerflex 525 manual download to remove powerflex 525 manual download the Power Module.
Re-attach the terminal guard when wiring is manuql. Use copper wire only. Unless specified in the individual distance poderflex as tested with the drive, these cables are not recommended and their performance against the lead length limits supplied is not known.
The corresponding input parameter t, t, t By default, start source is determined by P [Start Donload 1] and drive speed source is determined by P [Speed Reference1]. PowerFlex drives comply with the EN standards listed below when installed according to the installation instructions in this manual.
Without additional mitigation, radio powerflex 525 manual download interference is expected if used on dpwnload a network. The installer is responsible to take measures such as a supplementary line filter Page 45 Building structure steel 1 Some installations require a shielded enclosure. Keep wire length as short as possible between the enclosure entry point and the EMI filter. To simplify drive setup, the most commonly programmed parameters are organized in a single Basic Program Group.
Prepare for Drive Start-Up Page 48 Chapter 2 Start Up 4. The default control scheme is Source SRC. Terminal Blocks Programmable terminal functions. Communications Programmable communication functions.
Logic Programmable logic functions. Advanced Display Advanced drive operating conditions. Default is active. Start Used to start the drive. Press Enter or Sel to enter the group list opwerflex. Some features in the PowerFlex drive are not supported by older Drive Programming Powerflex 525 manual download configuration software tools. It is strongly recommended that customers using such tools migrate to RSLogix version See Program Group Parameters Programming and Parameters on powerfldx 57 for detailed descriptions of the parameters listed here, as well as the full list of available parameters.
See Language Support on page 51 for the languages supported by PowerFlex You canon g7 manual download not need to power up the control module. The main menu is displayed. Page Powerflex 525 manual download Parameters Chapter 3 Programming and Parameters About Parameters To configure a drive to operate powerflex 525 manual download a specific way, drive parameters may have to be set.
Each item is represented by a number. See AppView Parameter Groups on page for more information. See CustomView Parameter Group on page for more information. Custom Group This group can powerflex 525 manual download up to parameters. Does not pwoerflex slip frequency. Dkwnload 66 Chapter 3 Programming and Parameters Basic Display Group continued b [Power Saved] Related Parameter s : b Instantaneous power savings of using this drive compared to an across the line starter.
A reset or power cycle is required after selection is made. Sets the rated nameplate rpm of the motor. Powerflwx powerflex 525 manual download calculate the rated slip of the motor. To reduce the slip frequency, set this parameter closer читать больше the motor synchronous speed. Values Default: rpm Stop command clears active fault.
Changes adobe cs6 5.0 2 free these inputs take effect as soon as they are entered. P [Speed Reference1] is the factory default speed reference unless overridden.
Selects 2-Wire FWD for this input. Input must exceed 1. Page 83 Programming and Parameters Chapter 3 Terminal Block Group continued t [Anlg Loss Delay] Related Parameter s : t, t Sets the length of time after powrrflex during which the drive detects no analog signal нажмите чтобы перейти. Response to an analog signal loss is set oowerflex t t [Analog In x Loss].
Page 84 Chapter 3 Programming and Parameters Terminal Block Group continued t [Wake Time] Sets the analog input time dwonload drive must stay above to wake from sleep mode. Values Default: 0. Identifies the connections that powerflex 525 manual download be attempted on a reset or power cycle.
The following is a listing of the available settings for each digit. See Appendix D for more information. Logic for next step Digit 1 Logic to jump to a different step Values Default: Read Only Page 96 Chapter 3 Programming and Parameters Advanced Display Group continued d doownload Current] Rownload the current value poewrflex the motor torque current measured by the drive.
Sets pkwerflex PID output as trim to the source reference. Negative voltages are ignored and treated as zero. Settings Selects the encoder powdrflex.
Take appropriate precautions to guard against possible unintended speed or motion. See Chapter 4 for more information on faults and fault codes. Clear a Type 1 fault and restart the drive. The functions replicate the digital 255 options and function in the same way. The value is added to and subtracted from the target encoder unit value to create the tolerance range. See the детальнее на этой странице at A [Max Traverse].
Repetitive faults are only recorded once. This will indicate 0 if no address is set. Page Appview Parameter Groups Chapter powerflex 525 manual download Programming and Parameters AppView Parameter Groups PowerFlex drives include various AppView parameter groups that groups certain parameters together for quick and easy access based on different manuual of applications.
Page Drive Status Chapter Troubleshooting This chapter provides ссылка на продолжение to guide powerflex 525 manual download in troubleshooting the PowerFlex drive. Included is a listing and description of drive faults with possible solutions, when applicable. The integral LCD display provides visual notification of a fault condition by displaying the following.
No comments:
Post a Comment